HOW TO TILE A FLOOR

Thank you for joining us today at Fresh's Workshop. If this is your first visit, welcome! If you're returning, we appreciate your continued support.

This is the spot where we build and repair all kinds of cool stuff, along with making a ton of saw dust. (Man Glitter.)

During our last session in the Workshop, we fixed a water leak and a confused washing machine.

Click HERE to see that episode) 

Before we begin today's project, let's take a moment and talk about shop safety:

Be sure to read, understand and follow all of the safety rules that come with your power tools. Knowing how to use your power tools properly will greatly reduce the risk of personal injury. And remember this, there is no greater safety rule than to wear safety glasses.

Today, I'm tiling the floor of my office/radio room.

Back in 2017, when we purchased our retirement home, we opted for flooring. Having a dog, we ruled out carpet, and Penny was against tile.

Eventually, the flooring succumbed to the wear and tear from my office chair. I removed it, exposing the concrete beneath.

The concrete proved difficult to keep clean, prompting our decision to switch to tile.

In my previous office at our old home, we installed industrial-grade glued-down tile. It was costly and required extensive maintenance, leading me to discard this option.

We had also had good results with black and white self-adhesive tiles in a bathroom also at our former residence, so we're going with tile again.

This is the only picture I could find; that's 'Cooper' in the sink.

As mentioned, that floor remained in good condition, so we opted to use it again in my office. During a recent visit to Gainesville, we made a stop at an Ollie's Bargain Center.

And they had some tiles that Penny believed would look fantastic.

 

The first step is to calculate the number of tiles needed. Start by measuring the room's dimensions. Our room is 8 feet 4 inches by 7 feet 6 inches.  We would round up to 9 by 8 feet. Multiplying these numbers gives you 9 x 8 = 72, so we will require 72 square feet of tiles. 

The tiles at Ollie's are sold in packs of 25 square feet, so we purchased three packs.

The next step is to find the room's center, which is 5 by 8. Draw a diagonal line from one corner to its opposite, then repeat with the remaining corners. The intersection of these lines indicates the room's center. Or you can do it my way (see below)

That's the best drawing you can do ???  Hey, I never said I was Van Gogh

Returning to the floor.

Select a tile and position it at the center of the room as close as you think.

Ensure the tile is centered, providing equal distances to both the left and right walls.

Then, align the tile equidistantly to the north and south walls.

This establishes our starting point.

Mark two opposite corners with a marker.

All we do now is peel and press.

Ensure that all your tiles are oriented in the direction indicated by the arrow on them.

Now, you can proceed with laying the full tiles in the center of the room.

Utilize a large brush to remove any debris from the area.

Make sure the corners are exact. Press down firmly along all the seams with your fingers. Apply pressure to the center of the tile as well.

When encountering a smaller section, measure the gap and then mark the back of your tile, making sure the arrows are pointing in the correct direction. Ensure the fresh, uncut side is against the adjoining tile.

Utilize a ruler to score the tile at the marked line. Then, bend the tile and employ a razor knife to complete the cut.

Upon closer inspection, you may notice some tiles have slightly different colors. This discrepancy is due to the second box of tiles not matching the color indicated on the label. Such are the quirks of purchasing from a discount retailer. However, considering this is merely a closet and the tiles were 75% cheaper than the stick-on options at the home center, it's a compromise I'm willing to accept.

To prevent any issues, select your tiles more cautiously, or remove all the tiles and stagger them. You may even conceal them in a less visible area, such as beneath your desk.

Now that 75% of the tiles are in place, I think I'll take a break and come back to this project in a few days. I started today because I wanted to make sure we had enough tiles, and we do. We're going to Gainesville tomorrow, so I needed to know whether I should stop at Ollie's.

A few days have passed, and now I'm prepared to complete this project.

We had a great time in Gainsville.

Our 'go-to' spot for an Indiana Breaded Tenderloin sandwich is just north of the University of Florida Campus on 13th Street.

Let's complete the flooring. The constant up and down is exhausting; it's time to wrap this up.

With that, you now possess a beautifully tiled floor that will be easy to maintain.

For anyone worried that my chair might damage the floor, Penny has ordered a lovely rug for the room.

The threshold and moldings remain to be done... Another day. I am exhausted and parched.

I could have possibly achieved a superior result with higher-end tiles or by adhering them to the floor. Nevertheless, I chose not to undertake the extra expense and effort. Had I been tiling a primary room; I would have avoided the shortcuts taken in this project.

In summary, I am quite satisfied with the outcome. It is a considerable improvement over a mere bare concrete floor.

Next week, we'll revisit our lawn sprinkler system to address a defect that came to light during our recent water pipe repair.

Currently, I'm in the mood for a refreshing adult beverage.

See you soon!

Be sure to visit some of my other blogs:

AROUND THE KITCHEN  - SEE WHAT I COOK

BRIARWOOD - YOU CAN READ MY NOVELS

AUDIO CONSOLE - WHERE I AM BUILDING AN AUDIO MIXER

DISCLAIMER The information contained here is for ENTERTAINMENT purposes only. Working with woodworking tools can be dangerous. The user of these tools should have a basic knowledge of woodworking and be familiar with the proper use and safety precautions associated with these tools. Always wear appropriate personal protective equipment, such as safety glasses, ear protection, and a dust mask. Always use the tool in accordance with the manufacturer's instructions and guidelines. Always maintain a safe and organized work area.

God Speed, Mother Nature